View 41728001X-3_8036372.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

pc, hdmi, display port, sdi interface controller for tft panel model: alr-1920-sdi part number : 41728001X-3 or up instructions contents page: 2. introduction, how to proceed, usage note, disclaimer 3. system design ? diagram of a suggested system 4. assembly notes ? important information about system elements 6. connection & operation ? how to use the controller 10. connectors, pinouts & jumpers ? essential connection information 19. controller dimensions 20. application notes 22. troubleshooting 23. specifications 24. appendix i ? mode support table 27. appendix ii ? rs-232 control protocols 30. appendix iii ? mapping definition 32. appendix iv ? auto color gain 33. appendix v ? dv remote control unit work for alr-1920-sdi 34. warranty, caution & limitation of liability, trademarks 35. contact details it is essential that these instructions are read and understood before connecting or powering up this controller.
page 2 of 35 introduction designed for lcd monitor and other flat panel display a pplications, alr-1920-sdi is the single board solution for supporting argb, hdmi, display port, sdi input controller for driving the panel up to 1920x1200 resolution. this controller is the combo version for alr-1920 and hd-3000s. this product design for the monitor series : ? tft (active matrix) lcds with lvds interface of 1920x1200, 1920x1080, 1680x1050, 1600x1200, 1400x1050, 1440x900, 1366x768, 1280x1024, 1280x800, 1280x768, 1024x768, 1024x600, 800x600, 800x480, 640x480, 480x640 resolution ? support hdmi, vga, display port, sdi input ? support argb signal up to wuxga resolution. ? support hdmi 1.3 input up to 1080p/wuxga resolution. ? support single-link display port 1.1a ? support 1.5gbits & 3gbits bit rate sdi input signal support ? sdi re-clock loop through output. ? support lvds interface panel how to proceed ? ensure you have all parts & that they are correct, refer to: ? connection diagram (separat e document for each panel) ? connector reference (in following section) ? assembly notes ? check controller switch & jumper settings (errors may damage the panel) ? prepare the pc ? connect the parts ? understand the operation and functions (in following section) important usage note this product is for use by system developers and integrat ors, the manufacturer accepts no liability for damage or injury caused by the use of this produc t. it is the responsibility of the developer , integrators or other user of this product to: ? ensure that all necessary and appropriate safety measures are taken. ? obtain suitable regulatory approvals as may be required. ? check power settings to all component parts before connection. ? understand the operation and connectivity requirements of this controller. disclaimer there is no implied or expressed warranty regarding this material.
page 3 of 35 system design a typical lcd based display system utilising this controller is likely to comprise the following: summary: 1. lcd panel 2. lcd controller card, alr-1920-sdi 3. lvds cable (for c onnection with lvds panel) 4. inverter for backlight (if not built into lcd) 5. inverter cable 6. osd switch mount control 7. osd controls cable 8. optional controller status led1 9. optional backlight status led2 10. optional ir sensor 11. rs-232 control port 12. analog vga input 13. display port input 14. hdmi input 15. sdi input 16. sdi re-clock loop out 17. audio jack (stereo) output from hdmi / display port / sdi 18. audio output (stereo) with amplication from hdmi / display port / sdi 19. spdif audio output 20. backlight status input 21. power input (12vdc) digital view offers a range of accessories such as listed above, to make up complete display solution.
page 4 of 35 assembly notes this controller is designed for monitor and custom di splay projects using 1920 x 1200, 1920 x 1080, 1680x1050, 1600x1200, 1400x1050, 1440x900, 1366x768, 1280x1024, 1280x800, 1280x768, 1024x768, 1024x 600, 800x600, 800x480, 640x480, 480x640 resolution tft panels with a vga, svg a, xga, sxga, uxga, wuxga signal i nput. the following provides some guidelines for installation and preparati on of a finished display solution. preparation : before proceeding it is important to familiarize your self with the parts making up the system and the various connectors, mounting holes and general layout of the controller. as much as possible connectors hav e been labeled. guides to connectors and mounting hol es are shown in the following relevant sections. 1. lcd panel : this controller is designed for typical lvds interfac e tft panels with panel voltage 3.3v or 5v or 12v lvds interface. due to the variation between manufacturers of signal timing and other panel char acteristics factory setup and confirmation should be obtained before connecting to a panel. (note: check panel power jumper settings before connection) 2. controller card: handle the controller card with care as static charge may damage electronic components. 3. lvds signal cable : in order to provide a clean signal it is reco mmended that lvds signal c ables are no longer than 46cm (18 inches). if loose wire cabling is utilized these can be made into a harness with cable ties. care should be taken when placing the cables to avoi d signal interference. additionally it may be necessary in some systems to add ferrite cores to the cables to minimize signal noise. 4. inverter : this will be required for the backlight of an lcd, some lcd panels have an inverter built in. as panels may have 1 or more backlight tubes and the power requirements for diffe rent panel models backlights may vary it is important to match the inverter in order to obtain optimum performance. see page 20 for the applicat ion notes ?inverter connection section for more informations. 5. inverter cables : different inverter models require different cables and different pin a ssignment. make sure correct cable pin out to match the inverter. using wrong cable pin out may damage the inverter. 6. osd switch mount controls : the following section discusses the contro ls required and the section on connectors provides the detail. the controls ar e minimal: on/off, backlight brightness (depends on inverter), osd (5 momentary buttons) analog vr type or (8 momentary buttons) digital type. 7. osd switch mount controls cable : the cables to the function switches s hould be of suitable quality and length so that impedance does not affect performance. generally lengt hs up to 1 metre (3 feet) should be acceptable. 8. controller status led (optional) : this led indicates the controller status . the pin direction of the led should be corrected for right colour indication. red colour stands fo r standby. green colours stands for signal on. the status led is an optional part only, can be unconnected. controller led status (led1) : state led color no signal & backlight off red no signal & backlight on orange with signal & backlight on green 9. backlight status led (optional) : this led indicates the backlight status. this f unction is only available when cnb2 are properly connected and the panel is support the backlight status function. backlight led status (led2) : state led color backlight fault red backlight normal green 10. ir sensor : it is an optional part only, can be unconnected if not using ir remote control. see appendix v for button definition. 11. rs-232 control interface : firmware upgrade and serial cont rol via this interface port. 12. analog vga input cable : as this may affect regulatory emission test resu lts and the quality of the signal to the controller, a suitably shielded cable should be utilized. 13. display port cable : support single-link display port 1.1a. plug the di splay port cable to the connector p4 on the controller board. 14. hdmi input : support hdmi 1.3 input up to 1080p/wuxga resolution. plug the hdmi cable to the connector p3 on the controller board. 15. sdi input : 3g/hd/sd-sdi signal input support. plug the coaxia l cable to the connector j2 on the controller board 16. sdi re-clock loop out : 3g/hd/sd-sdi re-clock loop out. recommend to connect less than 100 meter in good co-axial cable (e.g belden 1694a) between dv devices.
page 5 of 35 17. audio jack (stereo) output from hdmi / display port / sdi input : this port support stereo audio output from the hdmi / display port / sdi audio source inputted. the audio handling is same as hd-3000 where 2 channels (stereo) of audio converted to hdmi output. then the same hdmi audio handli ng as on the standard alr-1920. it requires to select the appropriate input source and select the audio port ? speakers? via osd menu under ?sound? > ?output? osd menu page. 18. audio output (stereo) with amplication from hdmi / display port / sdi input : this port support stereo audio output from the hdmi / display port / sdi audio source inputted. t he audio handling is same as hd-3000 where 2 channels (stereo) of audio converted to hdmi output. then the same hdmi audio handli ng as on the standard alr-1920. it requires to select the appropriate input source and select the audio port ?speaker s? via osd menu under ?sound? > ?output? osd menu page. this audio output will disable when audio jack (j1) being plugged. 19. spdif audio output : this port support spdif audio output from the hdmi / display port / sdi audio source inputted. the audio handling is same as hd-3000 wher e 2 channels (stereo) of audio convert ed to hdmi output. then the same hdmi audio handling as on the standard alr-1920. it requires to select the appropriate input source and select the audio port ?spdif? via osd menu under ?sound? > ?output? osd menu page. 20. backlight status input : it only functions when connecting wi th the panel which support back light status detection pin. 21. power input : 12vdc is required, this should be a regulated supply. although the contro ller provides power regulation for the lcd power this does not relate to the power supplied to the backlight inverter. if an unr egulated power supply is provided to an inverter any fluctuations in power may affect operation, performance and lifetime of the inverter and or backlight tubes. ? power safety : note that although only 12vdc is s upplied as ?power-in? a backlight inverter for panel backlighting produces significantly higher voltages (t he inverter does not connect to the ground plane). we strongly advise appropriate insulation for all circuitry. ? emi : shielding will be required for passing certain regulatory emissions tests. also the choice of external controller to pc signal cable can affect the result. ? ground : the various pcb mounting holes are connected to the ground plane. ? servicing : the board is not user serviceable or repairable. warranty does not cover user error in connecting up to the controller and is invalidated by unaut horized modification or repairs. ? controller mounting : it is recommended that a clearance of at l east 10mm is provided above and 5mm below the controller when mounted. additionally consideration s hould be given to: ? electrical insulation. ? grounding. ? emi shielding. ? cable management. note: it is important to keep panel signal cables apart from the invert er & backlight cables to prevent signal interference. ? heat & ventilation: heat generated from other sources, fo r example the backlight of a very high brightness panel may generate significant heat which could adversely affect the controller. ? other issues that may affect safety or performance. ? pc graphics output : a few guidelines: ? signal quality is very important, if there is noise or instab ility in the pc graphics output this may result in visible noise on the display. ? refer to graphics modes table in spec ifications section for supported modes. ? non-interlaced & interlaced video input is acceptable. important: please read the application notes section for more information.
page 6 of 35 connection & operation caution: never connect or disconnect parts of the display system when the system is powered up as this may cause serious damage. connection connection and usage is quite straight forward (it is useful to have the relevant connec tion diagram available at this time): 1. lcd panel & inverter: connect the inverter (if it is not built-in the panel) to the ccft lead connector of the lcd panel. 2. lvds type panels: plug the lvds signal cable direct to j3 (if necessary). insert the panel end of the cable to the lcd panel connector. 3. inverter & controller: plug the inverter cable to cnb1 and cna1 (if necessary). plug another end to the connector on the inverter. 4. function switch & controller: plug the osd switch mount cable to cnc1 on the controller board and another to the osd switch mount. 5. led 1 : plug in a 3-way with dual colour led to connector le d1 on the controller board for indicating the controller status. 6. led 2 : plug in a 3-way with dual color led to connector led2 on the controller board for indicating the backlight status. this function is only avail able when cnb2 are proper connected and the panel is support the backlight status function. 7. ir & controller: plug in a 3-way with ir sensor to connector ir1 on the controller board. 8. jumpers : check all jumpers are set correctly. details referring the connection diagram at http://www.digitalview.com/controllers/csg.php 9. jumpers & inverter & panel voltage: particularly pay attention to the settings of ja3, ja6, jb2, jb3. jb2 & jb3 are used for inverter control (read inverter specification and information on the jumper table to define the correct settings). ja3 & ja6 are used for panel voltage input (read panel specification and information on the jumper table to define the correct settings). 10. hdmi cable : plug the hdmi cable to the connec tor p3 on the controller board. 11. vga cable : plug the vga cable to the connector p1 on the controller board. 12. display port cable : plug the display port cable to c onnector p4 on the controller board. 13. sdi input cable : plug the coaxial cable to connector j2 on the c ontroller board for sdi input cable. plug another coaxial cable to j4 for re-clock loop out. recommend to connect less than 100 meter in good co-axial cable (e. g belden 1694a) between dv devices. 14. audio output jack / spdif audio connector : audio output ports cn1 & j1 support audio output (stereo) from the hdmi / display port and cn11 support audio spdif audio output from hdmi / display port audio source inputted. i t requires to select the audio port ?speakers? / ?spdif? via osd menu under ?sound? > ?output? osd menu page. 15. power supply & controller: plug the dc 12v power in to the c onnector pp1. you can consider to use digitalview mating power cable p/n 426013800-3, 160mm. 16. power on: switch on the controller board and panel by using the osd switch mount. caution : never connect or disconnect parts of the display system when the system is powered up as this may cause serious damage. controller led status (led1 & led1a) : state led color no signal & backlight off red no signal & backlight on orange with signal & backlight on green backlight led status (led2 & led2a) : state led color backlight fault red backlight normal green general: ? if you are using supplied cables & accessories, ensure they are correct for the model of panel and controller. ? if you are making your own cables & connec tors refer carefully to both the panel & inverter specifications and the section in this manual, ?connectors, pinouts & jumpers? to ensure the correct pin to pin wiring. pc settings the controller has been designed to take a very wide range of i nput signals however to optimize the pc?s graphics performance we recommend choosing 60hz vertical refresh rate ? this will not cause screen flicker. operation once the system has been connected and switched on there are a number of functions avail able to adjust the display image as summarized in the following sections. the settings chosen will be saved for each mode independently.
page 7 of 35 lcd display system settings note: by way of explanation the following refers to a set of sample buttons that may be obtained as an option. in addition to power on/off and connection for backlight brightness the controller provides an on screen display of certain functions which are controlled by 5 momentary type buttons (analog vr type) or 8 momentary type buttons (digital type): controls analog vr type digital type on/off ? turns controller board power on vr toggle switch on/off button brightness ? controls backlight brightne ss rotary vr brightness +/- buttons menu ? turns osd menu on or off (it will auto time off) (function with signal input only) menu button menu button select ? select function / confirm (under osd menu on state) sel dn sel dn move up to select individual rgb color level osd page (under osd menu on state) sel up sel up + ? increase the setting / moves the selector to the next function (under osd menu on state) + + - - decrease the setting / moves the selector to the previous function (under osd menu on state) - - reset to factory defaults press and hold sel dn button, then power on the controller press and hold sel dn button, then power on the controller switch to next input source (under osd menu off state) + + volume adjustment (under osd menu off state) sel up / sel dn sel up / sel dn on/off/brightness sel up sel dn + - menu analog vr type digital type analog 10k vr type osd switch mount uses p/n 410680550-3 or up digital 10k type osd switch mount uses p/n 416100520-3 or up
page 8 of 35 osd functions image brightness increase/decrease brightness level. press ? or + (- + ) total : 100 steps contrast increase/decrease contrast level. press ? or + (- + ) total : 100 steps sharpness increase/decrease sharpness level. press ? or + (- + ) total : 8 steps color auto : auto rgb calibration ([see appendix iv] in details) (function in argb mode only) color temp 4 (adjust the warmness of the image displayed. the higher temperature the coolest image loo ks like. the lower temperature the warmest image looks like. function in argb mode only) 4200k 5000k 6500k 7500k 9300k user 4 r press ? or + (- + ) total : 100 steps g press ? or + (- + ) total : 100 steps b press ? or + (- + ) total : 100 steps reset gamma (0.4/0.6/1.0/1.6/2.2) display (function in argb mode only) auto adjust auto adjust the positions, phase, frequency phase fine tune the data sampling position (adjust image quality) press ? or + (- + ) total : 100 steps clock adjust the image horizontal size press ? or + (- + ) total : 100 steps display position adjust image position sound (function when hdmi, display port, sdi connected an d selected) volume increase/decrease volume level, total: 100 steps press ? or + (- + ) total : 100 steps mute mute output select audio output port speakers : via cn1 & j1 connector spdif : via cn11 connector system 4 input source select input : select the input video signal display port vga dvi/hdmi sdi autoscan : enable the auto source seek function osd menu timer : osd timeout in seconds 3 sec 6 sec 12 sec always on rotation : osd menu rotation in degree 0 90 180 270
page 9 of 35 position : adjust osd menu position transparency : set osd transparency press ? or + (- + ) total : 100 steps reset : load factory default settings. press down on osd keypad to factory reset temp reporting the on board temperature ( 0 c) [firmware version : v1.02.00 or up] items marked 4 have sub menus. exit the osd menu to save the setting chosen on board temperature reading : this controller has a built in on board temperature sensor on u4 which can report the on board temperature reading on osd menu. (see below) : on board temperature reading on osd menu
page 10 of 35 connectors, pinouts & jumpers the various connectors are: summary: connectors ref purpose description cn1 audio output (stereo) with amplication from hdmi / display port / sdi jst 4-way, s4b-zr-sm4a (mating type : zhr-4) (matching connection cable p/n 426685400-3) cn2 reserved for internal firmware upgrade for sdi part circuitry jst 6-way, b6b-xh-a (matching type : xhp-6) cn3 reserved for factory use only. cn4 reserved for factory use only. cn6 reserved for factory use only. cn7 serial control db9 female connector cn11 spdif audio output jst 2-way, s2b-zr-sm4a (mating type : zhr-2) (matching connection cable p/n 426007400-3) cna1 auxiliary power output jst 4-way, s4b-xh-a (mating type : xhp-4) (matching cable p/n 426040200-3) cnb1 backlight inverter jst 5-way, s5b-xh-a (mating type : xhp-5) (matching cable p/n 426058300-3) cnb2 backlight status input jst 2-way, s2b-xh-a (mating type : xhp-2) (matching cable p/n 426020800-3) cnc1 osd controls hirose df13a-12p-1.25h (mating type : df13-12s-1.25c) (matching osd switch mount cable p/n 426122200-3 (150mm) or 426122210-3 (250mm) hdmi1a reserved no function hdmi1a1 reserved no function ir1 infra-red sensor connector molex 53261-0371, 3 way 1.25mm pitch (mating type : 51021-0300) (matching connection cable p/n 426031500-3) ir3 infra-red sensor ir sensor on board led1 dual color led connector for controller status jst 3-way, s3b-zr-sm4a (mating type : zhr-3) (matching connection cable p/n 426031400-3) led2 dual color led connector for backlight status jst 3-way, s3b-zr-sm4a (mating type : zhr-3) (matching connection cable p/n 426031400-3) j1 audio jack (stereo) output from hdmi / display port / sdi 3.5mm phone jack j2 sdi input bnc connector j3 lvds panel signal jae fi-re51s-hf (mating type : jae fi-re51hl) j4 sdi re-clock loop through output. bnc connector p1 argb signal input db-15 way high density 3 row p3 hdmi signal input hdmi connector (type a) p4 display port input display port connector pp1 power input molex 43650-0200 compatible (mating type : molex 43645-0200 compatible) (matching power cable : p/n 426013800-3, 160mm)
page 11 of 35 summary: jumpers setting ref purpose note led3a reserved reserved for internal use only led1a1 reserved reserved for internal use only ja3 panel power voltage select see panel voltage setting table 1 caution: incorrect setting will cause panel damage ja6 panel power voltage select see panel voltage setting table 1 caution: incorrect setting will cause panel damage jb1 backlight brightness voltage range 1-2 closed = 3.3v max 2-3 closed = 5v max jb2 backlight inverter on/off control ? signal le vel 1-2 = on/off control signal ?high? = +12v 2-3 = on/off control signal ?high? = +5v open = on/off control signal ?high? = open collector caution : incorrect setting can damage inverter. jb3 backlight inverter on/off control ? polar ity 1-2 = control signal ?high? = ccft on 2-3 = control signal ?low? = ccft on jb5 backlight control type selection 1- 2 = vr/digital switch mount control 3-4 = analog backlight brightness control via rs-232 command (0xe0) ? voltage range 0~5v 5-6 = reserved jb6 backlight status 1-2, 3-4 clos ed = backlight status low ? normal 1-3, 2-4 closed = backlight status high - normal open = backlight status not used jp1 reserved reserved for internal programming use (always 1-2 closed) jp2 reserved reserved for internal use only jp3 reserved reserved for internal use only jp4 reserved reserved for internal use only jp5 reserved reserved for internal use only jp6 reserved reserved for internal use only jp7 reserved reserved for internal use only jp8 reserved reserved for internal use only jp6 input power control short = external switch control open = switch mount control jp13 reserved reserved for factory use jp14 reserved reserved for factory use sw1 panel selection see table below sw2 panel selection see table below sw4 reserved reserved for internal use only table 1 : panel voltage setting table : input voltage via pp1 panel voltage ja3 ja6 jumper on board 3.3v 3v3 closed 1-3 & 2-4 5v 5v closed 1-3 & 2-4 12vdc 12v open 5-7 & 6-8 caution: incorrect setting can damage panel & controller
page 12 of 35 ja3 & ja6 location on board : (please pay attent ion to the jumper settings on ja3 & ja6 which are red in color on board) ! ja3 ! ja6
page 13 of 35 dip switch selection ? sw1 pos #1 pos #2 pos #3 pos.#4 description panel resolution for wuxga panel off off off off samsung ltm220cs01 (tested) 1920x1200 au optronics b170uw02 v0 1920x1200 on off off off au optronics m215hw01 (tested) 1920x1080 samsung ltm230ht01 1920x1080 for uxga panel on off off off nec nl160120bc27-14 1600x1200 for wxga panel on off off off samsung lta260w2-l01 1366x768 on on off off samsung lta460ws-l03 1366x768 off off on off sharp lq315t3lz24 / au optronics m156xw01 v0 1366x768 on off on off lg lc420w02-a4 1366x768 off on on off nec nl12880bc20-02d 1280x800 off on off off nec nl12876bc26-21 1280x768 on on on off au optronics m220ew01 1680x1050 for sxga panels on off off on nec nl128102bc29-01b 1280x1024 on on on off fujitsu flc48sxc8v 1280x1024 off on off on sharp lq181e1lw31 1280x1024 on on off on samsung ltm170et01 1280x1024 off off on on au optronics m190eg01 1280x1024 for xga panel off off on on auo m150xn07 v2 (tested) 1024x768 off on on off lg lm151x2 1024x768 on on off on sharp lq150x1lgb1 1024x768 sharp lq150x1lgn2a 1024x768 on off on on nec nl10276bc12-02 1024x768 off on on on nec nl10276bc13-01c 1024x768 on on on on nec nl10276bc30-18/ 30-18c 1024x768 nec nl10276bc20-08 1024x768 for svga panel off off on off primeview pd104sl5h2 800x600 sharp lq121s1dg11 800x600 sharp lq104s1dg21 800x600 sharp lq121s1dg41 800x600 on off on off toshiba ltm12c289 800x600 off on on off sharp lq084s3dg01 800x600 on on off off sharp lq121s1lg41 800x600 nec nl8060bc21-02 800x600 on on on off sharp lq104s1dg21 800x600 off off off on primeview pd104sl5 800x600 for wvga panel on off on off nec nl8048bc19-02 800x480 on off off on sharp lq070y3lg4a 800x480 others on on on off au optronics m200rw01 v1 (tested) 1600x900 on off off off sharp lq150f1lh22 1400x1050 on on off off samsung ltm190m2-l31 1440x900 on off on off lg lm171wx3-tla1 1440x900 off on on off lg lm171wx3 (tested) 1440x900 off off on off cpt claa102na0acw 1024x600 for additional and recent added panels, s ee alr-1920-sdi panel support table at http://www.digitalview.com/controllers/csg.php
page 14 of 35 pos #5 pos #6 pos #7 description off off off wuxga on off off uxga off on off sxga on on off wxga off off on xga on off on svga off on on vga / wvga on on on others sw1 pos 8 = reserved. dip switch selection ? sw2 pos. # function description 1 panel pixel format off : double pixel on : single pixel 2 lvds data mapping select on : mapping a (lvds panel) off : mapping b (lvds panel) please adjust to get the correct pictur e. see as appendix iii for details of mapping a and b. 3 reserved reserved 4 reserved reserved the most current list can be found the controller solution generator at http://www.digitalview.com/controllers/csg.php
page 15 of 35 cn1 ? audio output (stereo) with amplication from hdmi / display port : jst 4-way, s4b-zr-sm4a (mating type : zhr-4) pin symbol description 1 amp l- audio left channel (negative) 2 amp l+ audio left channel (positive) 3 amp r- audio right channel (negative) 4 amp r+ audio right (positive) cn7 ? serial control, db9 female connector pin symbol description 1 nc no connection 2 rs-232_tx rs-232 tx data 3 rs-232_rx rs-232 rx data 4 nc no connection 5 gnd ground 6 nc no connection 7 nc no connection 8 nc no connection cn11 ? spdif audio output jst 2-way, s2b-zr-sm4a (mating type : jst zhr-2) pin symbol description 1 spdif_out spdif audio out 2 gnd ground cna1 - auxiliary power output: jst s4b-xh-a (matching type : xhp-4) pin symbol description 1 aux power +12v dc, 500ma max 2 gnd ground 3 gnd ground 4 aux 5v +5v dc, 500ma max cnb1 ? backlight inverter connector: jst s5b-xh-a (matching type : xhp-5) pin symbol description 1 gnd ground 2 vbkl backlight power supply, +12vdc 3 blctrl backlight on/off control signal (refer to jb2 & jb3) 4 bvr_wip backlight brightness vr pin wip 5 bvr_a backlight brightness vr pin a cnb2 ? backlight status connector : jst b2b-xh-a (matching type : xhp-2) pin symbol description 1 bl_s backlight status signal 2 gnd ground cnc1 ? osd switch mount control, hirose df13a-12p-1.25h (mating type : df13-12s-1.25c) pin symbol description 1 pswin power button a 2 sw_on power button b 3 bvr_a backlight brightness vr pin a 4 bvr_wip backlight brightness vr pin wip 5 bvr_b backlight brightness vr pin b (470 ohm resistor to +5v vcc) 6 gnd ground 7 menu osd menu 8 -/left osd -/left 9 +/right osd +/right 10 sel_dn osd select down 11 sel_up osd select up 12 nc no connection ir1 ? infra-red sensor connector: molex 53261-0371, 3 way 1.25mm pitch (matching type : molex 51021-0300) pin symbol description 1 gnd ground 2 stdby_vcc stand by voltage 3 ir data ir data
page 16 of 35 j3 ? lvds output connector: jae fi-re51s -hf (matching type : jae fi-re51hl) pin symbol description 1 vdd (+12v) panel power supply (+ 12v) (selected by ja3 & ja6) 2 vdd (+12v) panel power supply (+ 12v) (selected by ja3 & ja6) 3 vdd (+12v) panel power supply (+ 12v) (selected by ja3 & ja6) 4 vdd (+12v) panel power supply (+ 12v) (selected by ja3 & ja6) 5 vdd (+12v) panel power supply (+ 12v) (selected by ja3 & ja6) 6 vdd (3,3v/5v) panel power supply (3 ,3v/5v) (selected by ja3 & ja6) 7 vdd (3,3v/5v) panel power supply (3 ,3v/5v) (selected by ja3 & ja6) 8 vdd (3,3v/5v) panel power supply (3 ,3v/5v) (selected by ja3 & ja6) 9 vdd (3,3v/5v) panel power supply (3 ,3v/5v) (selected by ja3 & ja6) 10 vdd (3,3v/5v) panel power supply (3 ,3v/5v) (selected by ja3 & ja6) 11 gnd ground 12 gnd ground 13 gnd ground 14 gnd ground 15 gnd ground 16 nc no connection 17 nc no connection 18 nc no connection 19 nc no connection 20 gnd ground 21 gnd ground 22 nc no connection 23 nc no connection 24 txa3+ positive differential lvds data bit a3 25 txa3- negative differential lvds data bit a3 26 gnd ground 27 txac+ positive lvds clock for a channel 28 txac- negative lvds clock for a channel 29 gnd ground 30 txa2+ positive differential lvds data bit a2 31 txa2- negative differential lvds data bit a2 32 txa1+ positive differential lvds data bit a1 33 txa1- negative differential lvds data bit a1 34 txa0+ positive differential lvds data bit a0 35 txa0- negative differential lvds data bit a0 36 gnd ground 37 nc no connection 38 nc no connection 39 txb3+ positive differential lvds data bit b3 40 txb3- negative differential lvds data bit b3 41 gnd ground 42 txbc+ positive lvds clock for b channel 43 txbc- negative lvds clock for b channel 44 gnd ground 45 txb2+ positive differential lvds data bit b2 46 txb2- negative differential lvds data bit b2 47 txb1+ positive differential lvds data bit b1 48 txb1- negative differential lvds data bit b1 49 txb0+ positive differential lvds data bit b0 50 txb0- negative differential lvds data bit b0 51 gnd ground
page 17 of 35 led1 ? dual color led connector for controller status, jst 3-way, s3 b-zr-sm4a (mating type : jst zhr-3) pin description 1 green led pin (anode) 2 led pin common (cathode) 3 red led pin (anode) led2 ? dual color led connector for backlight status, jst 3-way, s3 b-zr-sm4a (mating type : jst zhr-3) pin description 1 green led pin (anode) 2 led pin common (cathode) 3 red led pin (anode) p1 - analog vga input ? db-15 way high density 3 row pin symbol description 1 pcr red, analog 2 pcg green, analog 3 pcb blue analog 4 id2 reserved for monitor id bit 2 (grounded) 5 dgnd digital ground 6 agnd analog ground red 7 agnd analog ground green 8 agnd analog ground blue 9 ddc_5v +5v power supply for ddc (optional) 10 dgnd digital ground 11 id0 reserved for monitor id bit 0 (grounded) 12 ddc_sda ddc serial data 13 hs_in horizontal sync or composite sync, input 14 vs_in vertical sync, input 15 ddc_scl ddc serial clock
page 18 of 35 p3 ? hdmi connector pin symbol description 1 data2+ tmds data2+ 2 data2s tmds data2 shield 3 data2- tmds data2? 4 data1+ tmds data1+ 5 data1s tmds data1 shield 6 data1- tmds data1? 7 data0+ tmds data0+ 8 data0s tmds data0 shield 9 data0- tmds data0? 10 clk+ tmds clock+ 11 clk@ tmds clock shield 12 clk- tmds clock? 13 cec cec 14 nc no connection 15 scl scl (i2c serial clock for ddc) 16 sda sda (i2c serial data line for ddc) 17 cec/gnd ground 18 +5v +5 v power (max 50 ma) 19 hpdet hot plug detect p4 ? display port input pin symbol description 1 ml_lane 0 (p) lane 0 (positive) 2 gnd ground 3 ml_lane 0 (n) lane 0 (negative) 4 ml_lane 1 (p) lane 1 (positive) 5 gnd ground 6 ml_lane 1 (n) lane 1 (negative) 7 ml_lane 2 (p) lane 2 (positive) 8 gnd ground 9 ml_lane 2 (n) lane 2 (negative) 10 ml_lane 3 (p) lane 3 (positive) 11 gnd ground 12 ml_lane 3 (n) lane 3 (negative) 13 config1 connected to ground 1) 14 config2 connected to ground 1) 15 aux ch (p) auxiliary channel (positive) 16 gnd ground 17 aux ch (n) auxiliary channel (negative) 18 hot plug hot plug detect 19 gnd ground 20 dp_pwr power for connector (3.3 v 500 ma) pp1 - power supply (mating type : molex 43645-0200 compatible) pin description 1 +12vdc 5a max 2 ground
page 19 of 35 controller dimensions the maximum thickness of the controller is 18.3mm (meas ured from bottom of pcb to top of components, including any underside components & leads). we recommend clearances of: ? 5mm from bottom of pcb - if mounting on a metal plate we also recommend a layer of suitable insulation material is added to the mounting plate surface. ? 10mm above the components ? 3~5mm around the edges any of the holes shown above can be used for mount ing the pcb, they are 3.2mm in diameter. caution: ensure adequate insulation is provided fo r all areas of the pcb with special attention to high voltage parts such as the inverter.
page 20 of 35 application notes using the controller without buttons attached this is very straightforward by following the steps below : ? firstly setup the controller/display system with the buttons. with controls attached and display system active make any settings for colour and image position as required then switch everything off. ? use a jumper to close jp6 jumper, this will fix the board on. ? refer to inverter specifications for det ails as to fixing brightness to a desired level, this may require a resistor, an open circuit or closed circ uit depending on inverter. inverter connection there are potentially 3 issues to c onsider with inverter connection: ? power ? enable ? brightness please read the following sections for a guide to these issues. inverter power : as per the table for cnb1 pin 1 is ground and pin 2 pr ovides dc12v dc . this should be matched with the inverter specification: see table. cnb1 pin description 1 ground 2 +12vdcvdc remark: for higher power inverter, more curr ent (for 12v) can be taken from cna1 pin 1. maximum current drawn on cna1 pin 1 and cnb1 pin 2 is 3a(12v) enable : this is a pin provided on some inverters for on/off function and is used by this panel controller for vesa dpms compliance. if the inverter does not have an enable pin or the enable pin is not used then dpms will not be operational. pin 3 should be matched to the inverters specificati on for the ?enable? or ?disable? pin. cnb1 pin description 3 enable further, jumpers jb2 & jb3 should be set to match the inverter s specification for the enable pi n power and high or low setting: see table. ref purpose note jb2 inverter enable voltage 1-2 h = 12v, 2- 3 h = 5v (vcc), open h = open collector jb3 inverter control 1-2 h = on, 2-3 l = on brightness : there are various methods for brightness control and it is impor tant to consider the specific ations for the inverter to be used. generally the situation is: ? brightness can controlled by using a re sistor or vr (variable resistor). ? brightness controlled by adding a circuit such as pwm (pulse width modulation). ? no adjustment of brightness is possible. cnb1 pins 4 & 5 are available for c onnecting to an inverter or circuit where vr control is supported. cnb1 pin description 4 vr wip 5 vr a this can then be matched with function controls (osd switch mount) pins 3 & 4: see cable design below .
page 21 of 35 design guideline for making vr circuitry : cnb1 ? backlight inverter connector: jst b5b-xh-a (matching type : xhp-5) pin symbol description 1 gnd ground 2 vbkl +12vdc, backlight power s upply (selected by ja3 & ja6) 3 blctrl on/off control (enable) ? see jb2 & jb3 4 bvr_wip brightness vr - wip 5 bvr_a brightness vr a cnc1 ? control switch, jst b12b-xh-a (matching type : xhp-12) pin symbol description 1 pswin power button a 2 sw_on power button b 3 bvr_a backlight brightness vr pin a 4 bvr_wip backlight brightness r pin wip 5 bvr_b backlight brightness vr pin b (470 ohm resistor to +5v vcc) 6 gnd ground 7 menu osd menu 8 -/left osd -/left 9 +/right osd +/right 10 sel_dn osd select down 11 sel_up osd select up 12 nc no connection the vr for brightness depends on the inverter. the main power load for on/off is handled by a relay on the controller. example for circuit design : signal description / notes : 1) r1 : 470ohm on board 2) rpot is an external potentiometer (in-line dip style) that can be plugged directly into cnc1 pins 3,4,5. rpot must be supplied / installed by user. 3) bvr_b : voltage tapped from ?top? of potentiometer, the node of r1 and rpot. 4) bvr_wip : voltage tapped from wiper arm of rpot. 5) bvr_a : voltage tapped from ?bottom? of rpot. note : bvr_a voltage is left floating on the controller board. to use this circuit, you need to tie this point to a potential (usually gnd, available at cnc1 p in 6 ) . 1.)choose rpot = 10k 2.) tie bvr_a to gnd 3.) circuit analysis gives bvr_wip as the following (see figure 1) bvr_wip = 5 x (rbc/10.47) where bvr_wip is in volts. and rbc is the resistance from the wiper arm to bottom of pot in kohms. to evaluate, plug in different values of rbc : rbc bvr_wip 0 0 v 2.5 k 1.2 v 5 k 2.4 v 7.5 k 3.6 v 10 k 4.8 v so this circuit could provide brightness adjust voltage ranging from 0v to 5v.
page 22 of 35 troubleshooting general a general guide to troubleshooting a flat panel display system it is worth considering the system as separate elements, such as : ? controller (jumpers, pc settings) ? panel (controller, cabling, connection, panel, pc settings) ? backlight (inverter, c abling, backlight tubes) ? cabling ? computer system (display settings, operating system) through step by step cross checking with instruction manuals and a pr ocess of elimination to isolate the problem it is usually possible to clearly identify the problem area. no image: ? if the panel backlight is not working it may still be possible to just see some image on the display. ? a lack of image is most likely to be caused by incorrect connec tion, lack of power, failure to provide a signal or incorrect graphic card settings. image position: if it is impossible to position the image correctly, ie the image adjustment controls will not move the image far enough, then test using another graphics card. this situation can occur with a cust om graphics card that is not close to standard timings or if something is in the graphics line that may be affecting the signal such as a signal splitter (please note that normally a signa l splitter will not have any adverse effect). image appearance: ? a faulty panel can have blank lines, failed sections, fli ckering or flashing display ? incorrect graphics card refresh rate, resolution or interl aced mode will probably cause the image to be the wrong size, to scroll, flicker badly or possibly even no image. ? incorrect jumper settings on the controlle r may cause everything from total failure to incorrect image. caution: do not set the panel power input incorrectly. ? sparkling on the display: faulty panel signal cable. backlight: items to check include: power input, controls, inverter and tubes generally in this order. if half the screen is dimmer than the other half: ? check cabling for the inverter. ? for a specific backlight tube check the ac pins or ientation (caution: never reverse any dc power pins). also: ? if adjusting brightness control has no effe ct the chances are that the vr rating or method of adjusting brightness is not compatible or correctly connected to the inverter. ? if system does not power down when there is a loss of signal continued failure: if unit after unit keeps failing c onsider and investigate whether you are short circuiting the equipment or doing something els e seriously wrong. generally after common sense issues hav e been resolved we recommend step by step s ubstitution of known working parts to isolate the problem.
page 23 of 35 specifications panel compatibility 1920x1200, 1920x1080, 1680x1050, 1600x1200, 1400x1050, 1440x900, 1366x768, 1280x1024, 1280x800, 1280x768, 1024x768, 1024x600, 800x600, 800x480, 640x480, 480x640 resolution tft lvds lcd?s support. no. of colours up to 3 x 8 bit providing 16.7 million colours. vertical refresh rate wuxga, uxga, wxga, sxga, xga, svga, vga resolution up to 60hz. dot clock (pixel clock) maximum 165 mhz graphics formats standard wuxga, uxga, sxga, xga, svga, vga standard input at source - vga analog (15-pi n) standard with automatic detection of : digital separate sync sync-on-green composite sync - hdmi (v1.3) - display port (1.1a) - sdi controls available - on/off - brightness (inverter) - osd menu - osd select - osd setting + - osd setting - control interface - buttons, rs-232, ir remote control settings memory settings are stored in non volatile memory language osd support graphics osd icons vesa dpms implementation yes plug & play vesa ddc 1, 2/b compatible supported sdi serial interface standard smpte 292m, 259m-c, 424m, 425m (level a) supported sdi video mode 576i50 (pal) 480i60 (ntsc) 720p60/59.94/50 (4:2:2) 1080i60/59.94/50 (4:2:2) 1080p60/50 (4:2:2) number of sdi channel input port supported 1 sdi re-clock loop through output yes afd (active format description) support at sdi port. yes embedded digital audio supported with stereo voltage output for lcd +3.3v , +5v, +12v the current drawn for 3.3v, 5v or 12v panel from 12vdc power input is limited to 3a. input voltage 12vdc , 5a max +/- 5% controller power consumption appr ox 9.6w (controller logic only, no panel and inverter are involved) controller dimensions 185mm x 93.5mm x 18.3mm storage temperature limits -40 o c to +70 o c operating temperature limits 0 o c to +60 o c notes please note the following: ? for specific panel setup a sample of an lcd may be requir ed (this will be returned) and a copy of the full technical specifications for the panel from the manufacturer. ? relayout and custom development services are available.
page 24 of 35 appendix i ? mode support table argb (p1) port : mode resolution clk [mhz] horizontal freq [khz] vertical freq [hz] sync mode t_70 720x400 70hz 28.322 31.469 70.087 digital separate sync t_70 720x400 70hz 28.322 31.469 70.087 sync on green v_60 640x480 60hz 25.175 31.469 59.940 digital separate sync v_60 640x480 60hz 25.175 31.469 59.940 sync on green v_60 640x480 60hz 25.175 31.469 59.940 composite sync sv_60 800x600 60hz 40.000 37.879 60.317 digital separate sync sv_60 800x600 60hz 40.000 37.879 60.317 sync on green sv_60 800x600 60hz 40.000 37.879 60.317 composite sync x_60 1024x768 60hz 65.000 48.363 60.004 digital separate sync x_60 1024x768 60hz 65.000 48.363 60.004 sync on green x_60 1024x768 60hz 65.000 48.363 60.004 composite sync sx_60 1280x1024 60hz 108 63.81 60.020 digital separate sync sx_60 1280x1024 60hz 108 63.81 60.020 sync on green sx_60 1280x1024 60hz 108 63.81 60.020 composite sync ux_60 1600x1200 60hz 162 75.000 60 digital separate sync ux_60 1600x1200 60hz 162 75.000 60 sync on green ux_60 1600x1200 60hz 162 75.000 60 composite sync wux_60 1920x1080 60hz 172.8 67.5 60 digital separate sync wux_60 1920x1080 60hz 172.8 67.5 60 sync on green wux_60 1920x1080 60hz 172.8 67.5 60 composite sync wux_60 1920x1200 60hz 193.2 74.5 60 digital separate sync wux_60 1920x1200 60hz 193.2 74.5 60 sync on green wux_60 1920x1200 60hz 193.2 74.5 60 composite sync
page 25 of 35 hdmi (p3) port : mode resolution clk [mhz] horizontal freq [khz] vertical freq [hz] t_70 720x400 70hz 28.322 31.469 70.087 v_60 640x480 60hz 25.175 31.469 59.940 sv_60 800x600 60hz 40.000 37.879 60.317 x_60 1024x768 60hz 65.000 48.363 60.004 sx_60 1280x1024 60hz 108 63.81 60.020 ux_60 1600x1200 60hz 162 75.000 60 wux_60 1920x1080 60hz 172.8 67.5 60 wux_60 1920x1200 60hz 193.2 74.5 60 1080p60 1920x1080p 60hz 135 67.5 60 1080i60 1920x1080i 60hz 74.14 33.7 60 1080i50 1920x1080i 50hz 74.184 28.1 50 720p60 1280x720p 60hz 74.25 45 60 576p50 720x576p 50hz 26.9568 31.2 50 480p60 720x480p 60hz 26.9568 31.4 60 display port (p4) port : mode resolution clk [mhz] horizontal freq [khz] vertical freq [hz] t_70 720x400 70hz 28.322 31.469 70.087 v_60 640x480 60hz 25.175 31.469 59.940 sv_60 800x600 60hz 40.000 37.879 60.317 x_60 1024x768 60hz 65.000 48.363 60.004 sx_60 1280x1024 60hz 108 63.81 60.020 ux_60 1600x1200 60hz 162 75.000 60 wux_60 1920x1080 60hz 172.8 67.5 60 wux_60 1920x1200 60hz 193.2 74.5 60 1080p60 1920x1080p 60hz 135 67.5 60 1080i60 1920x1080i 60hz 74.14 33.7 60 1080i50 1920x1080i 50hz 74.184 28.1 50 720p60 1280x720p 60hz 74.25 45 60 576p50 720x576p 50hz 26.9568 31.2 50 480p60 720x480p 60hz 26.9568 31.4 60
page 26 of 35 sdi (j2) port mode 576i50 (pal) 480i60 (ntsc) 720p60 (4:2:2) 720p59.94 (4:2:2) 720p50 (4:2:2) 1080i60 (4:2:2) 1080i59.94 (4:2:2) 1080i50 (4:2:2) 1080p60 (4:2:2) 1080p50 (4:2:2)
page 27 of 35 appendix ii ? rs-232 control protocols rs-232 serial control (baud rate 2400, 8 bits, 1 stop bit and no parity ) physical connection : controller side computer side connector interface : cn7 connector interface : serial port mating connector : db9 female mating connector : db9 male pin# description pin# description 2 rs-232 tx data 2 rs-232 rx data 3 rs-232 rx data 3 rs-232 tx data 5 ground 5 ground software connection : the osd function can be controlled through sending the rs-232 protocol. the rs-232 program can be custom-made to fit for application or it can be used the program provided by digitalview on request. please contact your local sales for informations. 1. commands to implement switch mount control buttons function command description acknowledge (if enabled) menu 0xf7 menu button pressed button equivalent select-down button 0xfa select down button pressed button equivalent select-up button 0xfb select up button pressed button equivalent right/+ button 0xfc right/+button pressed button equivalent left/- button 0xfd left/- button pressed button equivalent 2. parameter setting - immediate, relative, reset and query function command description acknowledge (if enabled) volume control - left + right channel 0x80, ?a? | ?a?, nn | ?+? | ?-?| ?r? | ?r? | ??? set audio (l+r) volume = value/increment/decrement reset query volume left + right volume control - on/off (mute) 0x80, ?m? | ?m?, ?0? | ?1?| ?r? | ?r? | ??? disable audio output enable audio output reset query ?0? ? audio off (muted) ?1? ? audio on brightness control 0x81, nn | ?+? | ?-? | ?r? | ?r? | ??? set brightness = value/increment/decrement reset query brightness. range: ?0??0?-?6??4? default: ?3??2? contrast control 0x82, ?a? | ?a?, nn | ?+? | ?-? | ?r? | ?r? | ??? set all contrast = value/increment/decrement reset query contrast. range: ?4??0?-?6??4? default: ?3??2? phase # 0x85, nn | ?+? | ?-? | ??? set dot clock phase = value/increment/decrement query dot clock phase. (in argb mode only) image h position # 0x86, nnnn | ?+? | ?-? | ??? set img_hpos = value/increment/decrement query image horizontal position. (in argb mode only) image v position # 0x87, nnnn | ?+? | ?-? | ??? set img_vpos = value/increment/decrement query image vertical position. (in argb mode only) sharpness 0x8a, nn | ?+? | ?-? |?r? | ?r? | ??? set sharpness= value/increment/decrement reset query sharpness range: ?f??c?-?0??4? default: ?0??0? frequency # 0x8b, frequency = frequency adjustment 5 4 6 3 1 7 8 9 mating face of rs-232 db9 male mating face of rs-232 db9 female 5 4 6 3 1 7 8 9
page 28 of 35 nnnn | ?+? | ?-? | ??? value/increment/decrement query (in argb mode only) osd h position 0x90, nnn | ?+? | ?-? | ?r? | ?r? | ??? set osd_hpos = value/increment/decrement reset query osd horizontal position range: ?0??0??0?-?3??e??8? default: ?1??f??4? osd v position 0x91, nnn | ?+? | ?-? | ?r? | ?r? | ??? set osd_vpos = value/increment/decrement reset query osd vertical position range: ?0??0??0?-?3??e??8? default: ?1??f??4? select menu timeout 0x93, nn | ?+? | ?-? | ?r? | ?r? | ??? select menu timeout = value/increment/decrement reset query osd menu timeout value. ?00? ? continuous. value ? round up to nearest available step. if value > max available step, set it to the max available step. ?0? ?0? ? always on. ?0? ?c? ? 12 seconds (default) ?0? ?6? ? 6 seconds ?0? ?3? ? 3 seconds input main select * function in valid mode only 0x98, nn | ?+? | ?-? | ?r? | ?r? | ??? select input main = pc or video or next available reset query main selected. ?0x41,0x31? argb (default) ?0x45,0x31? hdsdi ?0x48,0x31? hdmi ?0x50,0x31? display port gamma value select 0x9d, n | ?r? | ?r? | ??? select gamma value = value reset query gamma value: ?0? ? 0.4, ?1? ? 0.6 ?2? ? 1.0 (default), ?3? ? 1.6 ?4? ? 2.2 colour temperature select 0xb3, n | ?r? | ?r? | ??? select colour temperature = value reset query main selected. ?0? ? user defined rgb values. ?1? ? 4200k. ?2? ? 5000k. ?3? ? 6500k. ?4? ? 7500k. (default) ?5? ? 9300k. red level for selected colour temperature 0xb4, nn | ?+? | ?-? | ?r? | ?r? | ??? set the level of the red channel for the selected colour temp. = value/increment/decrement reset query red level for selected colour temperature. range: ?0??0?-?6??4? default: ?6??4? green level for selected colour temperature 0xb5, nn | ?+? | ?-? | ?r? | ?r? | ??? set the level of the green channel for the selected colour temp. = value/increment/decrement reset query green level for selected colour temperature. range: ?0??0?-?6??4? default: ?6??4? blue level for selected colour temperature 0xb6, nn | ?+? | ?-? | ?r? | ?r? | ??? set the level of the blue channel for the selected colour temp. = value/increment/decrement reset query blue level for selected colour temperature. range: ?0??0?-?6??4? default: ?6??4? backlight brightness control 0xe0, nn | ?+? | ?-? | ?r? | ?r? | ??? set backlight brightness = value/increment/decrement reset query backlight brightness. range: ?0??0?-?f??f? default: ?f??f? e.g ?1??0? ? 0xe0 0x31 0x30 * this control can only function when jb5 sets 3-4 closed
page 29 of 35 * apply for inverter control voltage in range of 0~5v. each step interval is in 1 backlight on/off control 0xe1, ?0? | ?1? | ?r? | ?r? | ??? set backlight brightness = disable backlight enable backlight reset query backlight on/off. osd menu lock 0xf6, n | ?0? | ?1? | ?r? | ?r? | ??? osd menu lock off/ on reset query ?0? ? osd menu lock off ?1? ? osd menu lock on # - function in argb mode only 3. other control function command description acknowledge (if enabled) select rs-232 acknowledge 0xc1, ?0? | ?1? disable/enable command acknowledge. ?0? ? acknowledge disabled. ?1? ? acknowledge enabled. auto-setup # 0xc3 start auto-setup of current vmode. ?0? ? fail. ?1? ? successful. command availability 0xc4, n check whether a command is available. ?0? ? not available. ?1? ? available. auto-calibration # 0xc5 start auto-calibration of gain of the rgb amplifier. ?0? ? fail. ?1? ? successful. query bios version 0xcb, ?0? read bios version ?nnnn? = bios ver. ?nn.nn? query pcba number 0xcb, ?1? read pcba number ?nnnn? = pcba number alr-1920-sdi=?41728? load factory defaults 0xce reset all parameters to factory default value ?1? ? successful. # - function in argb mode only hex to ascii conversion table hex ascii hex ascii hex ascii hex ascii 0x30 0 0x41 a 0x61 a 0x2b + 0x31 1 0x42 b 0x62 b 0x2d - 0x32 2 0x43 c 0x63 c 0x3f ? 0x33 3 0x44 d 0x64 d 0x34 4 0x45 e 0x65 e 0x35 5 0x46 f 0x66 f 0x36 6 0x47 g 0x67 g 0x37 7 0x48 h 0x68 h 0x38 8 0x49 i 0x69 i 0x39 9 0x4a j 0x6a j 0x4b k 0x6b k 0x4c l 0x6c l 0x4d m 0x6d m 0x4e n 0x6e n 0x4f o 0x6f o 0x50 p 0x70 p 0x51 q 0x71 q 0x52 r 0x72 r 0x53 s 0x73 s 0x54 t 0x74 t 0x55 u 0x75 u 0x56 v 0x76 v 0x57 w 0x77 w 0x58 x 0x78 x 0x59 y 0x79 y 0x5a z 0x7a z
page 30 of 35 appendix iii ? mapping definition ? definition of mapping a :
page 31 of 35 ? definition of mapping b :
page 32 of 35 appendix iv ? auto color gain the auto color gain func tion is supported in the argb mode only and is designed to calibrate the controller to the incoming video signal. in order to calibrate correctly, the display must be displaying an image containing both black and white data (see illustration below) when the function is used. the internal processor of the video contro ller chip will then execute a process to adjust the relative values of the rgb signals to achieve t he best performance. the parameters of the corrected rgb values are then stored in the controller and are unaffected by the reset factory defaults function. warning - if the auto color gain is executed wit hout an appropriate image being displayed, then the process will set incorrect values and the display colo rs will be distorted. if this occurs, then it can either be corrected by performing the process correctly or if this is not possible then the reset color gain function can be used. this function will rese t the stored rgb values to a set of approximate values.
page 33 of 35 appendix v ? dv remote control unit work for alr-1920-sdi button function power button soft power on/off button. attention button use combined with digit keys to enable/disable the ir function. alr-1920-sdi : ?attention? + ?1? mute button ( ) switch to mute on/off mode. sel up ( ) / sel dn ( ) press this button to select the items in the osd menu. volume (-/+) button press the ?+? button to incr ease the volume and the ?-? to decrease the volume. + / - button use ?+? button to direct control the hotkey function for switching to next input source. in osd menu, pressing this button to adjust the settings. display button activate the osd menu display on screen. stop (vga) button press this button in the non osd menu display mode to select vga source. hdmi button press this button in the non osd menu display mode to select dvi source. hd-sdi 1 button press this button in the non os d menu display mode to select sdi source. p/n 559000106-3 : digitalview remote control unit (without dv logo silk screen printing) p/n 559000105-3 : digitalview remote control unit (with digitalview logo silk screen printing)
page 34 of 35 warranty the products are warranted against defects in workmanship and material for a period of three (3) year from the date of purchase provided no modificati ons are made to it and it is operated under nor mal conditions and in compliance with the instruction manual. the warranty does not apply to: ? product that has been installed incorrectly, this specifically in cludes but is not limited to case s where electrical short cir cuit is caused. ? product that has been altered or repaired except by t he manufacturer (or with the manufacturer?s consent). ? product that has subjected to misuse , accidents, abuse, negligence or unusual st ress whether physical or electrical. ? ordinary wear and tear. except for the above express warranties, the manufacturer disclaims all warranties on pr oducts furnished hereunder, including all implied warranties of merchantability and fitness for a parti cular application or purpose. the stated express warranties ar e in lieu of all obligations or liabilities on the part of the manuf acturer for damages, including but not limited to special, indir ect consequential damages arising out of or in connection with the use of or performance of the products. caution whilst care has been taken to provide as much detail as possible for use of this pr oduct it cannot be relied upon as an exhaustive source of information. this product is for use by suitably qualified persons who understand the nature of the work they are doing and are able to take suitabl e precautions and design and produc e a product that is safe and meets regulatory requirements. limitation of liability the manufacturer?s liability for damages to customer or others resulting from the use of any product supplied hereunder shall i n no event exceed the purchase price of said product. trademarks the following are trademarks of digital view ltd: ? digital view ? alr-1920-sdi
page 35 of 35 contact details digital view has offices in asia, europe and usa also an internet site: asia digital view ltd 16 th floor millennium city 3 370 kwun tong road kwun tong hong kong tel : (852) 2861 3615 fax : (852) 2520 2987 sales : hksales@digitalview.com europe digital view ltd. 6 marylebone passage, london, w1w 8ex uk tel: +44-(0)20-7631-2150 fax: +44-(0)20-7631-2156 sales: uksales@digitalview.com usa digital view inc. 18440 technology drive building 130 morgan hill, california, 95037 usa tel : (1) 408-782 7773 fax : (1) 408-782 7883 sales : ussales@digitalview.com website www.digitalview.com specifications subject to change without notice 3rd issue: 15 march, 2013 (alr-1920-sdi.doc) ? digital view ltd 2011-2013
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: digital view: ? 4172800xx-3

▲Up To Search▲

Price & Availability of 41728001X-3

	To Download 41728001X-3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .